Bar Stool – Counter Height

(1 customer review)

$5.00

Printable plans for a 26″ counter height bar stool with a curved saddle seat, built from two 2x4s and two 2x2s. Includes a printable seat template, a cut list with every 5 degree angle, 4 illustrated steps, and a tools and materials list.

Buy Now →

✓ Instant download · Personal use license · Secure checkout via Stripe

SKU: RE-BAR-STOOL Categories: , , ,

Description

Counter height bar stool plans with a curved seat, built from 2x4s

We were planning a small counter height spot in the house we were renovating, and I wanted stools a little nicer than a flat-topped box. I thought a curved seat needed tools I didn’t own, until I realized I could cut the curve into each seat board before gluing them up. So the seat is eight 2×4 strips, each cut to a printed template with a jigsaw, glued into a block, then sanded smooth into a saddle shape. The base is 2×2 legs at a 5 degree splay, pocket-screwed together. The whole stool comes out of two 2x4s and two 2x2s for about $10.

Watch the build

What you get

  • Printable PDF plan, instant download
  • Overall dimensions
  • Cut list with every 5 degree angle marked
  • Printable seat template for marking the curve on each board
  • 4 illustrated steps: seat, front and back frames, base, final assembly
  • Tools and materials list

Specs

  • Overall size: 26″ tall x 17″ wide x 12″ deep (counter height)
  • Seat: curved, glued up from eight 2×4 strips and trimmed to 17″
  • Build time: 1 weekend
  • Skill level: Intermediate
  • Estimated cost: about $10 (estimate from the plan)

Lumber you’ll need

  • 2 boards, 2x4x8′ (eight seat strips and four short base pieces)
  • 2 boards, 2x2x8′ (legs and rails; you can rip both from a single 2×4)

Hardware

  • 2-1/2″ pocket screws
  • 2-1/2″ wood screws
  • Wood glue

Tools you’ll need

  • Pocket hole jig
  • Drill/driver
  • Miter saw for the 5 degree cuts
  • Jigsaw or band saw for the seat curve
  • Belt sander
  • Router (optional, for easing the seat edges)
  • Clamps
  • Tape measure, pencil and safety equipment

Common questions

How do you get a curved seat without special tools? Trace the template onto each of the eight seat boards and cut the curve with a jigsaw or band saw before glue-up. Clamp the strips together, let the glue dry, trim the sides to 17″, then sand the top smooth with a belt sander.

Do I need a router? No. It’s optional. You can ease or round over the seat edges with a sander instead.

How is the base attached to the seat? With 2-1/2″ wood screws driven up through the base rails into the seat.

Want to see it first? The full build is on the blog: counter height bar stool. Need a lower, simpler seat for the shop? Check out my simple stool plans.

1 review for Bar Stool – Counter Height

    IMG 1185
    John Fortman
    Oct 17, 2026
    First time dealing with a pocket screw jig and edge gluing. (Learning curve.) Next time I might use a router and pattern to finish the edge-glued pieces. (It took a lot of belt-sanding to even out and shape the saddle after edge-gluing.) Using pine lumber made this a cheap project and they don’t clash with the maple cabinetry. Pleased with the results. Took a little longer than I thought, but I’m not woodworking expert. I misaligned a lower cross piece on one of these. Don’t tell!
    Reply from Jamison Rantz:
    John, your secret's safe with me. Nobody is spotting one cross piece from across the kitchen. Pocket screws and edge gluing on the same build is a lot of new stuff at once, so that's a solid first go. Thanks for the review
Add a review

Your email address will not be published. Required fields are marked *

Quick answers

Questions about this plan

How do I download my plan after purchase?
You will receive a download link in your order confirmation email. You can also log in at My Account → Downloads any time to re-download.
What format is the plan?
Every plan is a printable PDF designed for standard letter paper. View on screen in your shop, or print at home or your local print shop.
Can I sell what I build from this plan?
Yes — on a small scale. Most builders selling at local markets, online, or to friends are well within the license. Mass production or reselling the plan itself is not allowed. See the Plan License.
Do you offer refunds?
Digital downloads are generally final — see our Refund Policy. If there is a legitimate issue with the plan or your access, email support@rogueengineer.com.
Can I modify the plan dimensions or materials?
Yes — modify dimensions, materials, finishes, and joinery as you like for your own project. See the Plan License for what you can do with modified versions.